Stopping condensation in garage

Discussion in 'UK Motorcycles' started by deadmail, Dec 12, 2005.

  1. deadmail

    deadmail Guest

    I've got a garage roofed with asbestos.

    On cold, damp mornings the roof drips. Any suggestions on how to get
    around this?

    I've thought about lining the roof with insulation and foil-backed
    plasterboard. Any options that are cheaper than this? Some sort of
    spray on foam insulation that costs very little would be ideal...
     
    deadmail, Dec 12, 2005
    #1
    1. Advertisements

  2. deadmail

    Lozzo Guest

    said...
    Move.
     
    Lozzo, Dec 12, 2005
    #2
    1. Advertisements

  3. deadmail

    BGN Guest

    Remove the roof or move to a warm country where it never rains.
     
    BGN, Dec 12, 2005
    #3
  4. deadmail

    ginge Guest

    I'd have thought you'd still have the problem of trapped moisture, as
    insulation would only slow the process down.

    How about improving the ventilation, so that a limited amount of air can
    pass through the garage thus removing the condensation?
     
    ginge, Dec 12, 2005
    #4
  5. deadmail

    deadmail Guest

    There's open space at the front, back and sides. It's something
    asbestos seems to do, based on my observations of open farm buildings.

    I thought that sealing the 'roof' bit would keep the warmer air below
    the roof. In any case since it only happens occasionally it would
    (probably) dry out eventually... Chicken wire over the insulation may
    be wise though.
     
    deadmail, Dec 12, 2005
    #5
  6. Polyurethane foam spray insulation is the thing for agribuildings, but
    helluva pricey for small areas.

    Cheapest way would be fit rockwool or aeroboard batts to the underside,
    but you'd need to hold them up, which is where your chickenwire would
    come in.
    --
    Dave

    GS850x2 XS650

    On UKRM you're just a **** with opinions.
     
    Grimly Curmudgeon, Dec 13, 2005
    #6
  7. deadmail

    deadmail Guest

    I was worried that would be the answer.

    I think it's rockwoll, chickenwire and (foil lined) plasterboard then,
    at least that way if I paint it white I'll have decent lighting, maybe.

    Then again I bought two 500W halogen units on a stand, 19 quid...
    absolutely brilliant, turns night into day. Well, within a small area
    anyway.
     
    deadmail, Dec 13, 2005
    #7
  8. deadmail

    Nick noxx Guest

    I lined the shed roof and walls by glueing (with a building adhesive
    like Gripfix) foil backed Celotex. Much more efficient than Rockwool and
    the extra cost can be offset by the fact that you don't need to buy
    plasterboard. You can by second grade stuff on the interweb but I don't
    have the address to hand. 1" thick should do it.

    Nick
     
    Nick noxx, Dec 13, 2005
    #8
  9. deadmail

    sweller Guest

    Can't you use insulating boards that fit between the rafters with simple
    battens holding them in place.

    Or simply sheet the rockwool in place with plasterboard or hardboard.
     
    sweller, Dec 13, 2005
    #9
  10. deadmail

    deadmail Guest

    Belts and braces. If the rockwool were to get wet I'd like something to
    restrain it in case the plaster gets soaked and collapses...
     
    deadmail, Dec 13, 2005
    #10
  11. deadmail

    deadmail Guest

    message
    It's 'safe' asbestos.

    As a kid I put up a large sheds using the stuff. At the end of the days
    I'd be white with it due to the dust from the sawing...

    It's all paranoia about it and in any case I've got to die of something.
     
    deadmail, Dec 13, 2005
    #11
  12. deadmail

    platypus Guest

    It'll take them a week to cremate you.
     
    platypus, Dec 14, 2005
    #12
  13. deadmail

    Pip Guest

    They cremated George Best in Hemel Hempstead on Sunday.

    Look what happened to him.
     
    Pip, Dec 14, 2005
    #13
    1. Advertisements

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments (here). After that, you can post your question and our members will help you out.