Oops! I did it again

eric the brave said:

It's a washer - about a millimetre thick.

If you want - I'll actually measure mine for you Timo (not till next
weekend though cos mine is in the shop have a new clutch fitted on
Monday).

 

A drinks too wet without one.

 

Simon Atkinson was seen penning the following ode to ... whatever:

Hmm. You're not talking about the metal ring/washer that holds the
cush drive rubbers onto the wheel, are you?

According to the mechanic the bit I'm missing is sitting inside the
drive unit on the side with the five studs.

Might come in useful, that, cheers.

 

Blimey that's a blast from the past.....Didn't Frank Muir used to say that ?

D

 

Bzzt. That's Rich Tea biscuits, if this here McVite's mug is to be
believed.

 

Using the patented Mavis Beacon "Hunt&Peck" Technique, Oldbloke
<> typed

(Of a Nhonda bit)

Probably. If you can get me one to look at, or draw one with the
critical dimensions on it.

You are warned, however, that time maybe something of an issue over the
next month or so, so if you *do* want it doing, let me know ASAP.

 

Timo Geusch said:

No. Look in the Haynes BOL - page 7.23 - it's Item 4 in the diagram
(15.13 rear wheel components) I assume you are talking about? It's
prolly not even a millimetre thick.

It does sit in there - it sits right inside and is easy to miss and
difficult to remove (it sticks to the bottom of the housing it sits in).

NP.

 

4,3.

Wealthy golf accessory, we hear.

--
| ___ Salad Dodger
|/ \
_/_____\_ GL1500SEV/CBR1100XXX/KH500A8/TS250C
|_\_____/_| ..62661../..14297.../..3157./.19406
(>|_|_|<) TPPFATUICG#7 DIAABTCOD#9 YTC#4 PM#5
|__|_|__| BOTAFOT #70 BOTAFOF #09 two#11 WG*
\ |^| / IbW#0 & KotIbW# BotTOS#6 GP#4
\|^|/ ANORAK#17
'^'

 

*Quality*

 

Simon Atkinson was seen penning the following ode to ... whatever:

Yep, that's the puppy.

.... and if it falls out, hardly anybody will notice :-/.

 

Will you give the answer in tomorrow's edition?

 

Nigel Eaton was seen penning the following ode to ... whatever:

Cheers. I'll see if I can get one from a breakers first in the next
couple of days, otherwise I'll see if I can get the dimensions until
the end of the week.

 

Timo Geusch said:

I did worry that mine was missing after the rebuild - it took a while to
find it but it was there.

I'm sure it's nothing special - ring Honda at Power Road in Chiswick -
ask for customer services - they'll prolly send you one for free.

 

Simon Atkinson said...

No good ringing Power Road, Honda UK moved to Slough a couple of years
ago.

 

Using the patented Mavis Beacon "Hunt&Peck" Technique, Simon Atkinson
<> typed

(Of Timo)

Remember that story where some rock star type bloke fucked about with a
Roller and the factory bought it back so they could quietly scrap it?

Well, imagine the panic at Honda HQ on Monday morning when they find out
that Timo's got a Pan...

 

LOL

There'll be development engineers falling on their swords today, mark my
words.

 

Lozzo said:

It's a while since I've needed to ring them. They heard from me a few
times when I had the Firestorm.

 

You could always go and beat up VW there, tell 'em that I sent you (useless
bastards that they are at that location) ;-)